Can the B&W Continuum Weight Distribution System Be Connected On Incline?
Updated 04/28/2024 | Published 04/26/2024
Question:
Can the Continuum weight distribution load bar be connected to the spindle when the truck and trailer are at an angle, say if the truck is 45 degrees off from being in-line with the trailer? What about if the truck and trailer are out-of plane, say if the truck attitude is 15 degrees off from being in-plane with the trailer? I presume that the hydraulic cylinder should not be pressurized until the truck and trailer are in-line and in-plane with each other, but I would like to know if the load bar can at least be connected or removed at angles like this if all of the cylinder pressure has been released.
asked by: Alex D
Expert Reply:
Yes, it can! The B&W Continuum item # BW78FR can be hooked up to the trailer on uneven ground or at an angle. You are correct though you will want to wait until the tow vehicle and trailer are level and lined up before pressurizing the system.
Product Page this Question was Asked From
B&W Continuum Weight Distribution System w/ Sway Control for 2" Hitch - 16K GTW, 1.6K TW
- Weight Distribution Hitch
- WD With Sway Control
- Hydraulic System
- Fits 5 Inch Frame
- Fits 6 Inch Frame
- Includes Shank
- 2-5/16 Inch Ball
- Fits 2 Inch Hitch
- Allows Backing Up
- 1000 lbs
- 1100 lbs
- 1200 lbs
- 1300 lbs
- 1400 lbs
- 1500 lbs
- 700 lbs
- 800 lbs
- 900 lbs
- B and W
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: B&W Continuum Weight Distribution System w/ Sway Control for 2" Hitch - 16K GTW, 1.6K TW
- Shop: Tool Box
- Video: Buyers Products Class 4 Trailer Safety Chain with 1 Clevis Hook Review 337BSC3835
- Video: Comprehensive Review: B and B Tow Plug and Safety Chain Holder
- Q&A: How Does Sway Control Work on B&W Continuum Weight Distribution System 1,600 Lbs
- Q&A: Comparing B&W Continuum And Reese Strait-Line Weight Distribution Systems
- Q&A: Is There Room to Open the Tailgate with the B&W Continuum Weight Distribution System
- Search Results: wdh
- Shop: A-Frame Trailer Coupler - Yoke Latch - Black - 2" Ball - Weld On - 8,000 lbs
- Shop: Buyers Products A-Frame Trailer Coupler w Jack Hole - Auto Latch - 2-5/16" Ball - Weld On - 15K
- Shop: Complete Propane Tank Holder Mounting Kit for 20-lb Tanks - Black
- Shop: Timbren Silent Ride Suspension for Tandem Axle Trailers w/ 3" Round Axles - 7,000 lbs
- Shop: Shocker Hitch Air Cushioned Trailer Coupler - 2-5/16" Ball - Flat Plate Mount - 20K
- Shop: Brophy Safety Chain Mounting Bracket - 8-3/8" Long x 5/8" Diameter - Weld On - Qty 1
- Search Results: rv bumper bracket
- Search Results: sewer hose tube
- Search Results: sewer hose bumper
- Search Results: 3/8 chain
- Search Results: trailer breakaway kit
- Search Results: rv bumper
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: How to Measure for Trailer Hitch Drop
- Shop: Trailer Wiring
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
on Weight Distribution Hitch
