Replacement SpeedKnob for Yakima Dr. Tray Bike Racks

Question

Question:

Will this work for a Dr. Tray with 2inch receiver? I didnt see whether or not this was compatible with 1 1/4 or 2inch receivers.

asked by: Michael

0

Expert Reply:

Yes, it will so long as you have one of the following bike racks Y02473, Y02473-02475, Y02474, and Y02474-02475! The Replacement SpeedKnob for Yakima Dr. Tray Bike Racks item # 8880717 fits a mixture of 2" and 1-1/4" Dr Tray bike racks.

expert reply by: Jerred H

0

Answer 1

The correct replacement SpeedKnob for the Yakima Dr.Tray 2 Bike Platform Rack is actually the Replacement SpeedKnob and Wedge Assembly for Yakima Bike Racks part #8880717 which is slightly longer than the Replacement SpeedKnob and Wedge Assembly for…

view full answer...

Answer 2

We do have the parts that you need for your Yakima bike rack: - Replacement Rear Tray for Yakima Dr. Tray Bike Rack #Y86CR (this is the 8889013) - Replacement Rear Arm for Yakima Dr. Tray Bike Rack #Y26CR (this is the 8889016) The Replacement Rear…

view full answer...

Answer 3

You have a Yakima Dr. Tray Bike Rack for 2 Bikes that uses a 2" Receiver. The Yakima part number is 8002473 as we no longer carry this rack. The first 5 numbers are associated with your product part number. The other parts of the number identify…

view full answer...

Answer 4

Since you do not know your lock core/key number, the best option is going to be to replace the entire lock core with the Replacement Lock Core and Keys for Yakima Rack and Roll Trailer #8880553 (S307) or #8880551 (S305). As long as your lock is…

view full answer...

Answer 5

I reached out to my contact at Yakima regarding the speed knob on your Yakima FullSwing bike rack. The wedge on the end of the speed knob is not a seperately available part. You would need to purchace the Yakima #8880904 Replacement SpeedKnob. If…

view full answer...

Answer 6

Springs do not come with, nor are they required with the Replacement SpeedKnob for Yakima HoldUp EVO #8880904.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement SpeedKnob for Yakima Dr. Tray Bike Racks

Product Page this Question was Asked From

Continue Researching