Replacement Wheel Studs For A Lakota LQ Horse Trailer

Question

Question:

I have a Lakota LQ horse trailer and looking to replace the lug nuts with ones that DO NOT have decorative caps on them. The size is 9/16 and I need 32 lug nuts. Do you carry these?

asked by: Kat

0

Expert Reply:

Hi Kat,

Yes, for a 9/16" wheel stud I recommend the DeeMaxx Trailer Wheel Lug Nut # DE25GR. This lug nut fits 9/16" - 18 wheel studs. 18 threads per inch is pretty standard but if you wanted to go the extra mile to make sure they fit you can take a tape measure and count the amount of threads in one inch on your wheel studs to confirm that these are the correct fit.

expert reply by: Kevin C

0

Answer 1

For a single piece, 9/16" lug nut for your trailer we offer the DeeMaxx Trailer Wheel Lug Nut #DE25GR.

view full answer...

Answer 2

The equalizer in the Tandem-Axle Trailer Equalizer Kit #AP216 is 11-1/2" on center from the outer spring mounting holes when measuring horizontal separation. One hole will be 6" on center from the equalizer mounting hole center and the…

view full answer...

Answer 3

Hey Lucas, thanks for reaching out! We have the Equalizer for 2" Wide Slipper Springs #TREQ4541 that looks to match the description you're needing, but this doesn't come in a full-fledged kit because it's from a different…

view full answer...

Answer 4

Hi Ryan; I have attached a diagram below of the #TREQ1304 for your reference. Go ahead and compare these measurements to your current equalizer. If the distance between the holes lines up with yours this is what I would choose. The #APT6SE equalizer…

view full answer...

Answer 5

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Wheel Studs For A Lakota LQ Horse Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching