What Model Hollywood Racks Bike Rack is This

Question

Question:

Hi, can you tell me the model of this older type Hollywood hitch rack? its the type where you have to untighten each cradle to pull up, then tighten to lock, also has the fabric type bike straps instead of the rubber type, thanks.

asked by: Gildebrand N

0

Expert Reply:

It looks like you have an older version or the predecessor of the Road Runner trailer hitch mount bike rack. They had that lower stabilizer arm at the bottoms of the racks.

expert reply by: Michael H

0

click to enlarge

Answer 1

I can not confirm or deny if we have any replacement knobs for your Bauer bicycle rack without any information on the rack, however due to the age I am going to assume probably not. We do have the Replacement Bolt & Locking Knob for Surco 51953…

view full answer...

Answer 2

For your 2023 Subaru Outback, I recommend the Curt Trailer Hitch item #C69VV. This hitch is custom fit and bolts to your Subaru with included hardware. This is a class III hitch with a 2" receiver. I really like this hitch because it is an easy…

view full answer...

Answer 3

The difference between the Curt 13494, our part #C67JR, and 13570, our part #C69VV, trailer hitches is that 13494 has a hidden crosstube so all you see is the receiver, while the 13570 is more of a "classic" hitch that has the receiver…

view full answer...

Answer 4

Hello Joseph, yes there is! What you are looking for is the Anti-Rattle Hitch Lock and Cable Lock for 2" Hitch Mounted Bike Racks #e88RV. This will work with the Benton Bike Rack #B54VR, as well as the #B94FR and #B54FR so that the bike and rack…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What Model Hollywood Racks Bike Rack is This

Product Page this Question was Asked From

Continue Researching