Inner Diameter of Replacement Round Bar Adapter for Yakima SpinVice Clamps

Question

Question:

whats the diameter of the Round Bar Adapter for Yakima SpinVice Clamps?

asked by: Ian

0

Expert Reply:

I'm assuming you mean the inner diameter where it clamps around the crossbar. We don't have the # Y96KR at our local warehouse right now and Yakima doesn't have any dimensions available. What I can tell you is that it is designed to clamp onto bars with a diameter of 1-1/8" so the measurement be slightly larger.

expert reply by: Robin H

0

Answer 1

For your Yakima Rack and Roll Trailer #Y08107. I recommend the Yakima MegaWarrior Extra Large Roof Rack Cargo Basket - Steel - 74" Long x 48" Wide #Y07080-82. It can fit the 48" crossbar spread you're needing without requiring a…

view full answer...

Answer 2

The vast majority of rooftop mounted accessories nowadays work with all different kinds of crossbar shapes such as round, square, aero/elliptical and most factory crossbars. If you're having issues with the accessories moving when used with round…

view full answer...

Answer 3

It sounds like the Replacement Round Bar Adapter #Y96KR in your Yakima JayLow Kayak Carrier #Y04073 is either missing or damaged. These adapters are specifically designed to hold the JayLow carrier firmly on round crossbars like you have on your…

view full answer...

Answer 4

The Yakima part number #Y08111 is just the crossbars of Yakima Rack and Roll trailer which the correct size trailer for these 78 inch bars is the part #Y08107. This trailer would be able to accommodate both an e-bike and a trike.

view full answer...

Answer 5

Lets start with the trailer connector. I can tell you what the functions are so it will be easy to connect to the lights once we determine their functions. On a 4-Way, you will have one pin that is covered. That is the ground. Right next to it is the…

view full answer...

Answer 6

There are two options for getting your side marker/running lights wired up on your trailer and I included two diagrams for you to check out. Option A will be to follow one wire that starts at the 4 Flat and follows the trailer frame down one side,…

view full answer...

Answer 7

It is very likely that the wiring on your trailer has 2 Brown wires which carries the running lights on either side of the trailer like the wishbone style harness #A35W42B from Optronics does. You will want to verify this before connecting them to a…

view full answer...

Answer 8

The brown (running light) wires all run to each other as they carry the same circuit. The reason there is two browns on the trailer side is because there are running lights that are on both sides of the trailer. Aside from that all the rest of the…

view full answer...

Answer 9

You have it right so far, the 4-way connector is just as you have stated. Remember that Yellow has a L in it so that is the left side brake/turn signal and green has a R in it so that is the right side brake/turn signal. The colors for wiring a 7-way…

view full answer...

Answer 10

When you store the Yakima Rack and Roll Trailer #Y08106 the trailer will be approximately 6' long. The tongue would be need to be removed when stored so the extension won't add anything to the store height since it'd get removed anyway.…

view full answer...

Answer 11

When testing the brown wire on your trailer, all of the tail lights on the trailer should be activated. Since you are using a standard 4-wire harness on the trailer, you will need to make sure that you are using jumper wires to provide running light…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Inner Diameter of Replacement Round Bar Adapter for Yakima SpinVice Clamps

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching