Can Curt Trailer Wiring Harness # C45ZV be Used with LED Trailer Taillights

Question

Question:

Will this work if the trailer uses LED lamps? Currently, my little cargo trailer has incandescent bulbs, but Im considering upgrading.

asked by: Terry C

1

Helpful Expert Reply:

Hey Terry, yes the Curt trailer wiring harness part # C45ZV that you referenced is compatible with trailer lights that are LED.

expert reply by: Jameson C

1

Terry

3/20/2024

Thanks!

Answer 1

It would be totally fine to use the Curt Aux LED indicator lights part #C53201 with the trailer wiring kit #C45ZV on a daily basis. If you wanted to use these as a way to add to the taillights of your 2022 Chevy Bolt EUV they wouldn't wear out or…

view full answer...

Answer 2

I do have an option for you but there are currently no custom fit trailer wiring harness options for a 2023 Chevrolet Bolt EV. That said, we do still have a way for you to setup the vehicle with trailer lights without splicing and that's with the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Can Curt Trailer Wiring Harness # C45ZV be Used with LED Trailer Taillights

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching