Height of the etrailer Replacement Inner Jack Tube With Spring Return

Question

Question:

What is the height of this TJD-12000SP-FIP replacement leg? For a used leg on a TJD-12000SP-R2. Thank you.

asked by: Kelly S

0

Expert Reply:

Kelly, the Replacement Square, Direct Weld Jack Inner Tube with Spring-Return Drop Leg # TJD-12000SP-FIP measures 19" tall.

expert reply by: Bryce D

0

TJD-12000SP-FIP Height
(click to enlarge)

Answer 1

For your 12K Pacific Rim square jack the correct inner tube with drop leg is the part #TJD-12000SP-FIP. This is a direct replacement for the Ram/Pacific Rim 12K trailer jacks like #TJD-12000SP-F2, which are often used as OEM/factory units on newly…

view full answer...

Answer 2

We do have the Replacement Inner Tube with Drop Leg, Foot, and Pull Pin for Curt Heavy Duty Direct Weld Square Jack #C28957. This is a 3-1/2" x 3-1/2" square inner tube that is designed to replace the inner tube on the Curt 28512 jack. We…

view full answer...

Answer 3

The drop leg portion of the Replacement Square, Direct Weld Jack Inner Tube with Spring-Return Drop Leg #TJD-12000SP-FIP measured about 3" square and is about 19" tall. Please note that this part is a direct replacement for jacks…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Height of the etrailer Replacement Inner Jack Tube With Spring Return

Product Page this Question was Asked From

Continue Researching