Replacement Cap For Trailer Jack With 1-3/4" Inside Diameter Tube

Question

Question:

I need a cap for a trailer jack. The jack doesn't have the manufacturers name on it but the top of the tube is 1 3/4 ID. Any help would be greatly appreciated

asked by: Paul

0

Expert Reply:

The 2 Inch Replacement Cap # LC115863 is the cap you want for a round jack with 1-3/4" inside diameter jack tube.

expert reply by: Bud M

0

Answer 1

If you are looking for a replacement cap that fits a 2 inch outer diameter tube you would want #LC115863 or #PS500322. These fit an inner diameter of 1-3/4 inches and should fit your Shelby jack. You will want to measure to confirm fit, but this is…

view full answer...

Answer 2

We do have the cap you need, which is the Replacement Cap for etrailer and Ram Swivel Marine Jacks - 1,000 lbs #MJ-1000B-CP, which is designed for the MJ-1000B Series jacks The cap you referenced, the Replacement Cap for etrailer and Ram Swivel…

view full answer...

Answer 3

Sure we have plenty of replacement caps for RAM jacks, however I would need a bit more information to get you the right cap. For instance, if you had a TJA-2000S series jack then you could use the Replacement Cap for etrailer and Ram Sidewind A-Frame…

view full answer...

Answer 4

We have another Dutton Lainson jack cap that's slightly smaller than what you bought. The part #DL22354 has an outer diameter of 1.98 inches and is most likely what you need based on your picture. Since you are wanting to be extra cautious this…

view full answer...

Answer 5

We do have replacement caps available for swivel jacks. If this is an actual etrailer jack you need one of the following: -Replacement Cap #MJ-1000B-CP (for MJ-1000B Series) -Replacement Cap #MJ-1500B-CP (for MJ-1500B Series) I noticed you looked at…

view full answer...

Answer 6

Thanks for reaching out, Davide! I believe the Replacement Cap for etrailer and Ram Swivel Marine Jacks - 1,500 lbs #MJ-1500B-CP will work for your application as it has a 2.08" ID and a 2.19" OD (see attached).

view full answer...

Answer 7

Although I'm not sure what jack you have, we do have a handful of replacement caps for Ram jacks. Ram Square, Direct Weld, Sidewind Jack 10K - #TJD-12000-CP Ram Sidewind 2,000 lbs A-Frame Jacks - #TJA-2000S-CP Ram Swivel Marine MJ-1500B Series…

view full answer...

Answer 8

I went out to the warehouse and measured Replacement Cap #MJ-1500B-CP for you. The threaded part has a diameter of 2.08 inches. The overall diameter is 2.19 inches. I have included a picture showing these measurements.

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Cap For Trailer Jack With 1-3/4" Inside Diameter Tube

Product Page this Question was Asked From

Continue Researching