Replacement Cap for Trailer Jack with 2 inch Inside Diameter

Question

Question:

I need one that fits inside diameter 2 inches

asked by: Dave

0

Expert Reply:

Replacement Top Cap for Dutton-Lainson Jacks Item # DL6602 fits jacks with an outer tube diameter of 2.5 inches and inner tube diameter of 2 inches.

I went out and took some measurements for you (see photo). The ridges on the inside of the Replacement Cap # DL6602 have an outer diameter of 2.25 inches and an inner diameter of 1.90 inches.The flexible plastic ridges will ensure a tight fit and will work well inside your jack with an inner diameter of 2 inches.

expert reply by: Carla M

0

click to enlarge

Answer 1

We have another Dutton Lainson jack cap that's slightly smaller than what you bought. The part #DL22354 has an outer diameter of 1.98 inches and is most likely what you need based on your picture. Since you are wanting to be extra cautious this…

view full answer...

Answer 2

We do have replacement caps available for swivel jacks. If this is an actual etrailer jack you need one of the following: -Replacement Cap #MJ-1000B-CP (for MJ-1000B Series) -Replacement Cap #MJ-1500B-CP (for MJ-1500B Series) I noticed you looked at…

view full answer...

Answer 3

Replacement Mounting Hardware for etrailer and Ram Swivel Marine Jacks - 1,200 lbs and 1,500 lbs Item #MJ-1000B-MBB will actually be perfect for you. I checked the specs on the actual jacks that come with this hardware and it is basically identical…

view full answer...

Answer 4

The 2 Inch Replacement Cap #LC115863 is the cap you want for a round jack with 1-3/4" inside diameter jack tube.

view full answer...

Answer 5

If you are looking for a replacement cap that fits a 2 inch outer diameter tube you would want #LC115863 or #PS500322. These fit an inner diameter of 1-3/4 inches and should fit your Shelby jack. You will want to measure to confirm fit, but this is…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Cap for Trailer Jack with 2 inch Inside Diameter

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching