Replacement Brake Assemblies for Master Tow 80 Tow Dolly

Question

Question:

I have a Master Tow dolly 80 TH with surge brakes . This looks like the replacement I am looking for I was going to replace shoes as the inner grease seal failed but this seems like a good option . Pictures included of what I need to replace and Master tow info . Thank You Tony

asked by: Tony S

0

Expert Reply:

Hey Tony, yes the replacement hydraulic brake assemblies part # AKUBRK-35 is correct for what you sent in a picture of from your Master Tow dolly.

expert reply by: Jameson C

0

Answer 1

Good to hear from you again, Octane! Since your 2021 Chevy Spark is an automatic you will need to use a tow dolly, according to the online owner's manual. For this I recommend the Demco Kar Kaddy SS Tow Dolly with Disc Brakes #DM9713045 because…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

You sure can Mike. The etrailer Hydraulic Trailer Brakes item #AKUBRK-35 are going to work with your boat trailer's hubs. The only time you run into problems is going from hydraulic brakes to electric because you need a smooth surface for the…

view full answer...

Answer 7

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

Hey Larry! If your DA66B is the drum brake model the Demco Hydraulic Brake Actuator #DM72VR is the direct replacement. Since you were asking about the Hydraulic Brake Kit #AKFBBRK-7-D as well I'll assume that is correct. The brake mounting…

view full answer...

Answer 10

Hi Charles, While we don't currently offer the inner member that you're needing for the UFP A-70 we do offer a compatible replacement with the Dexter DX7.5L A-60 Brake Actuator #DX33FR. This is the entire actuator assembly along with the…

view full answer...

Answer 11

Hey Tony, I would want all free-backing plates on a boat trailer if it was me as it allows you to back up the trailer easier. Basically they prevent the brakes from applying if you were ever to need to back up on a flat surface or a up a hill.…

view full answer...

Answer 12

To check for a Free Backing Hydraulic Trailer Brake #AKFBBRK-35 you will need to remove your brake drum assembly. The free backing brakes have a different front brake shoe. This shoe is designed to fall away when the trailer is moving in reverse. The…

view full answer...

Replacement Brake Assemblies for Master Tow 80 Tow Dolly

Product Page this Question was Asked From

Continue Researching