Recommended Camper Tie Downs for a 2010 Chevrolet Silverado 2500 HD
Updated 02/16/2024 | Published 02/12/2024 >
Products Featured in This Question
Question:
Hello, Looking to get the front and rear tie downs for 2010 Silverado 2500HD Ext Cab, 4x4, Running boards only under cab dont extend under the bed, Factory installed hitch receiver with an open ended cross tube not 100 sure if this is factory but should be after googling a bit, picture attached Ive looked on your website and after applying filter, the only option available is happijac that I am not comfortable with. Ive started live chat and received same answer that HappiJac is the only option for my truck. I then went on TL website, applied the filter for my truck and they advised C2205 for the front and C3209 for the rear side. Can you please advise? Thanks, Matej
asked by: Matej Z
Expert Reply:
Matej, If you're not comfortable using Happijac tie downs then you can absolutely use the TorkLift Camper Tie-Downs # TLC2205 for the front, and # TLC3209 for the rear.
These are American made, custom fit to your vehicle so it'll bolt right up to the frame, and is virtually invisible when installed. You're also going to need a set of tie downs # TLS9526-2-LK to secure your camper to the tie downs.
Product Page this Question was Asked From
TorkLift Camper Tie-Downs - Custom Frame Mount - Front
- Truck Camper Tie Downs
- Front Tie-Downs
- Frame-Mounted
- Custom Fit
- Powder Coated Steel
- TorkLift
more information >
Continue Researching
- Shop: Gen-Y Hitch Receiver Hitch Extender for 2" Trailer Hitches - 14" Long
- Search Results: gen y
- Search Results: wieght distribution hitch
- Search Results: happijac
- Search Results: camper turnbuckles
- Shop: Camper Tie-Downs
- Shop: Equal-i-zer Weight Dist Shank - 18" Long - 7" Rise, 3" Drop - 600 to 1,400 lbs TW
- Search Results: 25 hitch extension
- Shop: Brophy Stake Pocket Mounted Camper Tie-Downs - Bed Mount - Qty 4
- Search Results: removable trailer tongue
- Search Results: hitch extension
- Shop: Equal-i-zer Weight Dist Shank - 18" Long - 8" Rise, 4" Drop - 600 to 1,400 lbs TW
- Q&A: Why Do Hitch Extenders Reduce Hitch Capacity but Long Ball Mounts Do Not
- Q&A: Recommended Hitch Extender w/a 7,500 lbs Capacity
- Q&A: Are Stake Pocket Tie-Downs Safe Enough To Secure A Truck Bed Camper on a 2010 Ford F-350?
- Video: TorkLift SpringLoad XL Turnbuckles for Frame-Mounted Camper Tie-Downs Spec Review
- Video: Feature Breakdown: Gen-Y Hitch Hitch Extender for 2" Trailer Hitches
- Shop: Trailer Hitch
- Shop: TorkLift Camper Tie-Downs - Custom Frame Mount - Rear
- Shop: TorkLift Tie Downs - Custom Frame Mount - Front and Rear
- Shop: HappiJac Original Turnbuckles for Camper Tie-Downs - Stainless Steel - Qty 4
- Q&A: Will Using A Hitch Extender Only Reduce The Tongue Weight By 50%
- Q&A: How Can I Safely Extend My Trailer out 12" While Using My ProPride 3P Weight Distribution System?
- Q&A: Recommended 2" Hitch Extender for a Truck w/ the Tailgate Down
- Q&A: Do Hitch Extenders Reduce Capacity by 50 percent Regardless of Length
- Shop: Suspension Enhancement
- Video: Breaking Down the Brophy Basic Turnbuckles w/ Hardware for Camper Tie-Downs
- Video: Clean Up Your Trailer Wiring
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)



Matej
2/13/2024
Thanks, that sounds great. Do you mind sending instructions for # TLC3209? Cannot find them. Wondering how they are getting installed on round tube hitch sides.