What Type of Grease is Used in etrailer Brand Trailer Axle Hubs

Question

Question:

e32gr has pre-greased hubs. What type grease was used, so I can use a compatible grease?

asked by: George

0

Expert Reply:

The etrailer brand axle # e32GR is pre-greased using a lithium complex multi-purpose grease like the # DX64TR.

expert reply by: Jameson C

0

Answer 1

Red lithium grease such as #L11390 is one we use often here for installations and it is compatible with other Lithium formulas. I have included a link to our help article that covers grease compatibility. There are greases that are not compatible…

view full answer...

Answer 2

The rebound clip on a leaf spring such as double-eye spring #e54SR will be positioned with about 1/2-inch of the shortest leaf sticking out past the clip. The clips do two things: they help maintain alignment of the various spring leaves but more…

view full answer...

Answer 3

You always need to keep your trailer tires filled to the max cold psi rating. If your current load range G tires have a 110 psi rating then that is what you need to keep them filled to. Tire blowouts are a result of damaging a tire (like hitting…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

What Type of Grease is Used in etrailer Brand Trailer Axle Hubs

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching