Recommended Trailer Hitch for a 2024 Ford F-250

Question

Question:

Do you have any hitches for a 2024 Ford F-250

asked by: Bill S

0

Expert Reply:

Yes, for your 2024 Ford F-250 we have the Curt Trailer Hitch Receiver # C15802. This is a class V 2 1/2" receiver that has a beefy 20,000 lb capacity, is assembled in the USA, and has an easy bolt-on install using the provided hardware.

expert reply by: Bryce D

0

Answer 1

Hello Ramon, The Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2" #C15802 is a great fit for your 2021 Ford F-350 XLT Tremor. It matches up to the existing holes in your frame, so no drilling is required. The vertical…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2" #C15802 has 3 different hole dimensions for mounting. The two holes closest to the receiver are 36.31 inches on center. The widest holes are 37 inches on center and…

view full answer...

Answer 3

Yes, it'll fit but you're not going to be able to get rid of that 5" filler strip. I took a look at the instructions for the Curt Hitch item #C15802 and the Ford factory hitch and they have similar, if not almost identical mounting…

view full answer...

Answer 4

I don't have an exact dimension I can give you but if you check out the picture I attached that shows the Curt hitch part #C15802 installed you can see that it installs basically in the exact same location as the factory hitch.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hey Nathan, the PowerMax panels like the part #PM59VR that you referenced use 12- VAC residential style miniature circuit brakers. Typical brands are ITE/Siemens, Murray, Crouse-Hinds, and Thomas & Betts.

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Recommended Trailer Hitch for a 2024 Ford F-250

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching