Load Resistor to Allow 2024 Lexus TX Detect Trailer with LED Taillights

Question

Question:

I have a new 2024 Lexus TX with a flat 4 pin connector and the vehicle isnt properly detecting my trailer because it has LED lights. Is there an easy way to add the necessary resistance so that it detectes the trailer? Thanks

asked by: Paul

0

Expert Reply:

Easiest way would be to add load resistors on each of the trailer wiring circuits with the part # P230004A. Each circuit would need a resistor so you'd need to install three.

expert reply by: Jameson C

0

Answer 1

Hello Trent, Since your other lights are working on the trailer but your running lights are not, have you tried to turn your headlights on? I know in my 2024 Chevy Silverado I have to have the headlights on in order for the running lights on my…

view full answer...

Answer 2

What you'd need is a 7-way adapter that has diodes built into the circuits which will absorb the small voltage spikes you are seeing with your Land Rover. For that you'd just need the part #C57003 and you'd be set.

view full answer...

Answer 3

There's not a wiring diagram for the ARC Lighting Load Resistor for LED Lights - Quick Splice #ARC22VR however the installation is pretty simple. All you're going to need to do is take one end of the resistor and connect it to the ground on…

view full answer...

Answer 4

Hey Christopher, thanks for reaching out! The WT21W LED Bulbs #ARC79GR you're looking at do not have a built-in resistor. For that you'll need the ARC Lighting Load Resistor for LED Lights #ARC22VR to prevent that hyperflashing.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Load Resistor to Allow 2024 Lexus TX Detect Trailer with LED Taillights

Product Page this Question was Asked From

Continue Researching