Recommended Trailer Brake Controller For a 2024 Toyota Tundra

Question

Question:

What trailer brake controller would you recommended for a 2024 Toyota Tundra?

asked by: Bill M

0

Expert Reply:

I recommend the Redarc Tow-Pro Liberty Brake Controller # RED24FR for your 2024 Toyota Tundra. This will easily connect to your factory wiring with the Plug N Play Wiring # RED49FR making for a simple installation. You can also use the Mounting Panel # RED48FR to install the control knob to your dash.

expert reply by: Bud M

0

Answer 1

The SumoSprings Solo Custom Helper Springs - Rear Axle #SS75FR you were looking at for your 2016 GMC Canyon will not void your warranty. This is due to the fact that you are protected by the Federal Magnusson-Moss Warranty Act which states that if…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hello Barry, Since you already have a weight distribution (WD) hitch and are only experiencing a little rear sag, I recommend going with SumoSprings. I typically only suggest Timbrens for those who are towing heavy loads regularly, as they can create…

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hello again Monty; I would get the black SumoSprings Custom Helper Springs #SS66PV. These have a capacity of 1,800 lbs so it gives you a bit over the blue without overdoing it. SumoSprings are a great choice if you don't want to go with the air…

view full answer...

Answer 11

Sure, I can help with that. I can see why the fitment notes are confusing. For a 2012 Toyota Tundra with the factory tow package and factory 7 way connector, you'll want a brake controller that plugs into the factory brake controller port under…

view full answer...

Answer 12

Hello Joe, Thanks for writing in! Based on the measurements you provided, the Gen-Y Glyder Shock Absorbing Ball Mount #325-GH-12001 is not the right fit for your setup. Since your Tundra's receiver measures 18 inches from the ground and your TAB…

view full answer...

Recommended Trailer Brake Controller For a 2024 Toyota Tundra

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching