Replacement Brake Shoes for Dexter 6k Nev-R-Adjust Brake Assemblies

Question

Question:

I need brakes shoes only for two Dexter 6000# Never adjust axles, both sides so 4 wheels total. Thanks.

asked by: Jim

0

Expert Reply:

Yes we do have replacement shoes for the Dexter 6k Nev-R-Adjust assemblies part # 23-458-459 with the part # K71-676 for the right hand side and the part # K71-675 for the left hand side.

expert reply by: Jameson C

0

Answer 1

Installing brakes on a trailer really isn't too bad. The install is pretty basic and a DIYer like yourself wouldn't have a problem at all. To determine the parts you need though we need to for sure know what axles/spindles you have so that we…

view full answer...

Answer 2

Certainly; the correct replacement brake shoes for the Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 12" #23-458 and #23-459 are the following: - Replacement Shoe and Lining for Nev-R-Adjust 12" x 2" Electric - Left Hand…

view full answer...

Answer 3

If you already have brake drums you will not have to replace them unless they are damaged or became overheated and have discoloration on the inside armature surface where the magnet rides, grooves in the armature surface, or severe wear where the…

view full answer...

Answer 4

I recommend using at minimum a 12 gauge wire like #12-1-1, but preferably 10 gauge wire like #10-1-1. When you try to run 12v power for electric brakes through a thinner 14 gauge wire to power something like your brakes it overloads the wire and…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Brake Shoes for Dexter 6k Nev-R-Adjust Brake Assemblies

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching