Replacement High Pointe RV Microwave 520EC028KD7S

Question

Question:

need to replace

asked by: Jerold R

0

Expert Reply:

If the microwave you have is the High Pointe 520EC028KD7S the correct replacement would be the High Pointe part # HP49ZR.

expert reply by: Jameson C

0

Michael

1/3/2025

Do you carry a replacement door for the 520EC028KD7S

Jameson C.

1/3/2025

@Michael I wish we did but at this time we do not have any replacement microwave doors.

Answer 1

Sometimes the RF Brake Controller part #TK94FR will not read the 00 in the pairing process. We had a customer who had a similar problem who found a way for the pairing process to complete without ever seeing the 00. Here's exactly what he sent…

view full answer...

Answer 2

I'm pretty sure that's to wire up a third brake light on a camper shell. To know for sure, take a circuit tester, like our part #PTW2993, and test that wire while applying the truck's brakes. If I'm correct it's a dedicated brake…

view full answer...

Answer 3

Hello Marie. Yes, the High Pointe Built-In RV Convection Microwave part #HP49ZR and the High Pointe model EC028KD7 are one and the same. The #HP49ZR is simply our own unique part number for this part. We use unique part numbers for many of our parts.…

view full answer...

Answer 4

The High Pointe Built-In Convection Microwave with Air Fryer #HP36ZR will fit as a replacement for your current ECO28KD7. It does appear the new unit will easily fit into place but as the RV manufacturer can build 2 units at the same time and they be…

view full answer...

Answer 5

Hey Troy, I have a few options for you to choose from, starting with the Greystone Built-In RV Convection Microwave #GR27FR. This is going to be the closest option dimensionally at 21" wide x 11" tall x 15-3/4" deep. The next option,…

view full answer...

Answer 6

Hey Paul, so the best option for you will be the Furrion Chill HE part #FR42PV as this covers everything you are looking for. It's the quietest and coldest blowing unit that also comes with an install kit designed to replace Dometic units like…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement High Pointe RV Microwave 520EC028KD7S

Continue Researching