Will the Curt Trailer Hitch Interfere With the Kick Sensors on a 2024 Lexus RX 350h

Question

Question:

Will the C29VV interfere with the kick sensor on a 2024 Lexus RX350H?

asked by: David P

0

Expert Reply:

The Curt Trailer Hitch Receiver # C29VV will not interfere with the kick sensor function on your 2024 Lexus RX 350h. To get it to work however, you'll have to kick to either side of the receiver instead of swiping your foot under the bumper for the sensors to pick up your foot movement.

expert reply by: Bryce D

0

Howie R.

4/20/2024

Having what I think is a common issue. 2024 Lexus RX350H. Hitch installed per instructions but kick sensor not working. Tried swiping foot everywhere left to right from left of receiver to right of receiver. No luck. Any other suggestions?

Bryce D.

4/22/2024

@HowieR Hey Howie, sorry to hear about the issues you're having and yes you are right it is a fairly common occurrence. What you can try to do is stick your head underneath the vehicle to make sure that none of the sensors are incorrectly positioned. Sometimes kick sensor can get lost with a trailer hitch, but this shouldn't be a problem with your vehicle.

Answer 1

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Will the Curt Trailer Hitch Interfere With the Kick Sensors on a 2024 Lexus RX 350h

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching