Availability Of A 15" Wheel With 5 On 5-1/2" Bolt Pattern

Question

Question:

I need a 15inch wheel with a 5x5.5 pattern and a 3 1/4inch apart. Can you help?

asked by: Angel

0

Expert Reply:

We do carry one wheel that fits those specifications with part # TA37RR. This is a 15" wheel with the 5 on 5-1/2" bolt pattern (holes 3-1/4" apart on center). It is important to note that this wheel is made with a -0.67" offset, so the tire will sit slightly farther from the trailer than it would with a standard non-offset wheel.

expert reply by: Jesse M

0

Answer 1

I was able to look at the picture of your trailer wheel/tire and see that the size is 7.00-15LT so for a wheel in the 15 inch diameter that has the 5 on 5-1/2 inch bolt pattern that you need we have one option with the part #TA37RR. Since your…

view full answer...

Answer 2

It sounds like you are just looking for the most economical way to add trailer tires and wheels with a 5 on 5-1/2" bolt pattern but are concerned they won't fit when you replace your axle. Realistically this is a valid concern and your axle…

view full answer...

Answer 3

The importance of matching a wheel's pilot hole diameter to the part of the hub that fits through it depends on the type of wheel. A hub-centric wheel uses the pilot hole to center the wheel on the hub and also to bear some of the total weight…

view full answer...

Answer 4

The Vesper Steel Modular Trailer Wheel w/ Offset - 15" x 5" Rim - 5 on 5-1/2 - Silver #TA37RR has a 4.25 inch pilot opening. The only time the size of the pilot opening is really important is if you're using a hub-centric wheel (which…

view full answer...

Answer 5

The pilot diameter on a wheel, like the one with part #AM30620, is the diameter of the bigger hole that is directly in the middle of the wheel. The pilot hole diameter of the wheel for the part I just measured is 2.84". I have attached a picture…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Availability Of A 15" Wheel With 5 On 5-1/2" Bolt Pattern

Product Page this Question was Asked From

Continue Researching