Male Pipe Dimensions for Installing Square Pipe Mount Swivel Jack on Trailer

Question

Question:

What are the dimensions of the mounting piece that comes with this? I want to compare it to what I currently have on my trailer to see if I need to have any welding done for this project or not.

asked by: JW

0

Expert Reply:

The weld-on bracket that comes with the Square Pipe Mount Swivel Jack w Footplate # TJDP-5000S-FLB measures 2-1/4" long and has 1-1/2" inner and 2" outer diameters.

I've attached a dimensional photo as well as some videos for you to check out. You can see the dimensions on the Replacement Male Pipe # TJP-IP58-CTN product page.

expert reply by: Jon G

0

Dimensions of Replacement Male Pipe for etrailer and Ram Pipe Mount Swivel Jacks
(click to enlarge)

Answer 1

Hey Marc, if you have the ability to apply the brakes with the manual override lever lots of times while moving slowly before needing to go on a trip then yes you can just install the brakes and not worry about an initial adjustment. It may take some…

view full answer...

Answer 2

Yes, The Square Pipe Mount Swivel Jack w Footplate #TJDP-7000S-B would be able to lift your trailer from the side to change a flat tire. The jack has a 7,000 pound lift capacity and has a 8,000 pound support capacity. The jack has a weld-on…

view full answer...

Answer 3

I wasn't able to find the dimensions of your current lights but there's definitely a wide variety of options that you can go with. You'll want to first measure the diameter of your lights and determine if they're surface mount and…

view full answer...

Answer 4

Hey Brian, if you grab the magnet and move it in the direction of the arm that it is attached to far enough it will click and it will adjust the star wheel tighter. This will be the easiest way to move the shoes out. Or you can install them and then…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The retracted bracket height dimension of the 12-5/8 inches that the Bulldog Jack part #BD190708 that you referenced has is measured from the bottom of the foot to the center of the pipe mount bracket on the side of the jack.

view full answer...

Answer 7

I went to our warehouse to provide you a few measurements of the Pro Series pipe mount swivel jack #PS1401080303. The length of the entire swivel jack in the retracted position is 26-3/4 inches. The foot plate is 3-3/4 inches wide and 7-1/2 inches…

view full answer...

Answer 8

Yes, to get two of the Global Link RV Entry Door Locking Latch Kit with Keyed Alike Option #295-000019 keyed alike you'll just have to select the drop down box by the add to cart button and choose keyed alike.

view full answer...

Answer 9

Yes, the Global Link RV entry door latching kit part #295-000019 can be ordered keyed alike. You get three latches that all work with the same key number. To order keyed alike change the drop down on the product page to keyed alike. However, they can…

view full answer...

Answer 10

Hello Wes; to make sure the #295-000003 and #295-000019 are keyed alike you have to choose "Keyed Alike" from the drop down box on the product page. Once you have made this selection all you need to do is add it to your cart and checkout.…

view full answer...

Male Pipe Dimensions for Installing Square Pipe Mount Swivel Jack on Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching