Torque Rating For the Four Bolts On The CE Smith Trailer Hub # CE13100

Question

Question:

CE13100? What is the torque tightening specification in foot-pounds for the four bolts on this hub with the tire/rim installed? I like to validate tightness with a torque wrench. Thanks for your help and support

asked by: Robert R

0

Expert Reply:

The bolts on the CE Smith Trailer Hub # CE13100 are to be tightened to 85-95 ft lbs.

expert reply by: Jesse M

0

Answer 1

Hello Mike. For lifting your 94 Jayco 1206 popup rv I recommend adding the Torflex Lift Kit - Single Axle - 2-5/8" Lift #K71-723-01. I would double check your axle weight capacity, this kit is good for a #9 Torflex axles with a 2,000-lb…

view full answer...

Answer 2

It sounds like you are needing the CE Smith Trailer Hub Assembly #CE13100. This hub fits on a 1" spindle and has the same 4 bolt lug pattern with the threaded bolts that screw into the hub. The grease seal used has the same 1.249" inner…

view full answer...

Answer 3

The Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased #AKIHUB-440-2-1K won't fit your trailer spindle as it will be too long. The reason is, this hub is designed to work on BT8 spindles, which are longer than…

view full answer...

Answer 4

There are some 4.80/4.00-8 trailer tires which use inner tubes and some that do not, I can't answer whether or not yours do for you. I can only speak to tubeless options as that is all we offer. If it's tubeless then you can simply replace…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Torque Rating For the Four Bolts On The CE Smith Trailer Hub # CE13100

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching