Inner Tube Diameter of Bulldog # BD150415 Sidewind Jack for Genie Basket Lifts

Question

Question:

What is the diameter of the pipe where the foot or wheel attaches?

asked by: Mike P

0

Expert Reply:

According to my Bulldog representative, the inner tube of the # BD150415 jack has a 2 inch outside diameter and a 1-3/4 inch inside diameter.

Keep in mind that in many cases the caster wheels are rated lower than the jack itself. Therefore, if you use a caster wheel like the # PS1400750340 that's rated at 1,200 lbs, the weight capacity of the jack will be reduced to 1,200 lbs.

expert reply by: Mike L

0

Answer 1

The foot on the inner tube on Pro Series trailer jack #PS1401480303 is attached, all one part, so you would not be able to add a wheel. None of the pipe-mount swivel jacks come with a wheel. Your best option would be to replace the jack with…

view full answer...

Answer 2

I recommend picking up the Aero Style Crossbar T-Slot Fit Kit #MPG8287 which comes with bolts, nuts, and washers that will fit in the Yakima HD Bar T-Slots like the 78" part #Y01159. If you're trying to find specific dimensions for your own…

view full answer...

Answer 3

Yes. You can mount an awning on Yakima Overhaul HD systems like the #Y01151-5855. If you wanted to use the Yakima Slim Shady Awning #Y36VR, that awning will mount using the included clamps to the HD bars on the Overhaul system. If you're wanting…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Inner Tube Diameter of Bulldog # BD150415 Sidewind Jack for Genie Basket Lifts

Continue Researching