Replacement 7-Way For 2000 Dodge Durango

Question

Question:

Due to a prior rearend wreck of my 2000 Dodge Durango, I need to replace the plug on the end of my tow wiring. It appears it was a 7 way circle plug with flat prongs in it. Will this product work? It has to have have the dodge rectangle plug on wiring end. Hopefully my pictures might help explain.

asked by: Michelle

0

Expert Reply:

We do have a replacement 7-way kit that fits your 2000 Dodge Durango that has the square connector you mentioned as well with the part # HM42190.

expert reply by: Jameson C

0

Durango 7-Way Connector 2000
(click to enlarge)

Answer 1

I believe that the photo you sent in is of the OBD-II port on your 2014 Toyota Tundra. This is useful if your vehicle is throwing codes but it is not used for the brake controller. As long as your Tundra has the factory 7-Way at the rear of the truck…

view full answer...

Answer 2

Easiest way to determine if your 2005 Dodge Dakota has the wiring needed to install a 7-way like the part #HM42190 would be to look behind the rear bumper for the square connector that this plugs into. I attached a picture of what the connector looks…

view full answer...

Answer 3

You can either take the VIN of your 2010 Dodge Dakota and reach out to your local Dodge dealer and they can confirm that for you or you can look at the trailer wiring on your Dakota. If it has a single square plug like what the Hopkins Wiring…

view full answer...

Answer 4

Thank you for your recent order. The part you purchased, Hopkins Endurance Quick-Install 7-Way Trailer Connector #HM42190, is intended as a direct plug-in replacement for a factory-installed 7-way trailer connector. This plugs in directly with no…

view full answer...

Answer 5

Since you have the factory tow package on your 2018 Jeep Wrangler Unlimited, the Hopkins Endurance Quick-Install 7-Way Trailer Connector #HM42190 will be an easy installation. The plug will be just behind the bumper and I've attached photos to…

view full answer...

Answer 6

All fuses and breakers needed for the operation of your brake controller should already be in place. You can check your owner's manual for the location of the fuses that manage the tow package. All you should have to do is plug in one end of the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement 7-Way For 2000 Dodge Durango

Continue Researching