What are the Dimensions of the etrailer Gooseneck Coupler Handle

Question

Question:

Can you tell me the diameter of the rod and length when in the locked position?

asked by: David H

0

Expert Reply:

I went out to the warehouse and measured the Gooseneck Coupler Handle # GCPN-HD and measured 8 1/2" overall, 3 1/4" for an overall height, 2 1/2" for an inside measurement, and is 12.95 mm (.5") thick.

I've attached a diagram showing these measurements for you to check out.

expert reply by: Bryce D

0

Answer 1

We only carry the springs for those heavy duty style ramps. For the springs we have the Ramp Spring - 2K Torque for 1-1/2" Shaft - left hand #RS16933LH and corresponding right hand #RS16933RH. The other parts will need to be either straightened…

view full answer...

Answer 2

Dexter recommends a SAE 90, SAE 80W-90 or SAE 75W-90 oil to be used. I recommend the Kodiak Synthetic Bearing Oil for Oil Bath Hubs #XLPROLUBE as it is a synthetic 90 weight oil that helps reduce friction and to keep bearings cool. Since your cap was…

view full answer...

Answer 3

As long as your dual wheel has a flat surface where the Flange Wheel Nut #95188 would rest against, like what the Dexstar Dual Wheel #AM20790 has, then you would use this flange wheel nut in the place of a nut with a 90 degree cone. Attached is a…

view full answer...

Answer 4

Ram gooseneck coupler #GCPN-25008 has set screws and a 7/8" diameter pin. The set screws are 3/4"-10 x 2-1/2". It is recommended to use a large crescent wrench to adjust the set screws since they have a square head instead of a hex…

view full answer...

Answer 5

There may be a solution for you with the Putco High Power Luminix Off-Road Light Bar #P10010, which is a 10" long light bar with a narrow 15-degree spot beam. It does mount to flat surfaces, has a wiring harness which allows it to connect to a…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Nelson, so you would need two separate systems since a supplemental braking system can only be used with a towed vehicle and a trailer brake controller can only control trailer brakes. Main difference is a supplemental braking system is designed…

view full answer...

What are the Dimensions of the etrailer Gooseneck Coupler Handle

Product Page this Question was Asked From

Continue Researching