Replacement Brake Assembly for Dexter 023-463-00

Question

Question:

hi there, im searching for brake assembly 023-463-00 dexter right hand. when i did my research ur website pop me up with the number of k23-463-00. i want to know if they are compatible? will they replace my 023-463-00? Thanks for ur answer

asked by: Vincent C

0

Expert Reply:

Yes, the Dexter brake assembly part # K23-463-00 is the same as the 023-463-00. This is the passenger side replacement brake assembly for a 4,400 lb trailer axle.

expert reply by: Jameson C

0

Answer 1

Hey Michael, thanks for reaching out! For brakes we have the kit #K23-462-463-00 for standard or the kit #K23-478-479 for Nev-R-Adjust, and then for a hub/drum assembly you're looking at the part #8-407-5UC3-EZ. Is there anything else you're…

view full answer...

Answer 2

According to Dexter, 10" Electric Brake Assemblies like the #K23-462-00 and #K23-463-00 should be secured to the axle with brake mounting hardware like the #BRKH10B. The #BRKH10B should be tightened to between 45-ft/lbs and 70-ft/lbs.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Brake Assembly for Dexter 023-463-00

Product Page this Question was Asked From

Continue Researching