Distance From Hitch Pin Hole to Sleeve of Hitch Extender e68YR

Question

Question:

What is the distance from the hitch side hole to the sleeve?

asked by: Peter

0

Expert Reply:

The distance from the hitch pin hole to the sleeve is 2 inches for the Trailer Hitch Extender for 1-1/4" Trailer Hitch Receivers - 7" Long # e68YR.

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 3

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 4

Unfortunately it will not Bill but congrats on the car! There's been two generation changes with big redesigns on the Corolla so the older hitch isn't going to be transferable. To add a hitch to your 2025 Toyota Corolla LE, I recommend the…

view full answer...

Answer 5

Hello Todd, great question. The Yakima EXO Swing Away and Gear Locker #Y62VR is going to allow you to open the rear doors on your 2025 Sprinter 3500XD RV at around 90 degrees. Then with the box removed you may face a clearance issue with your…

view full answer...

Answer 6

Hey William, so the 3 inch hitches do use the larger hitch pin diameter but the 2-1/2 inch hitches still use the smaller one. So with a reducer like the part #38735 technically you would use both sizes. If you check out the picture I attached you can…

view full answer...

Answer 7

Hey Jeremy. I have a solution for you but the etrailer item #e85ZV is not going to work. It's a high low adapter that's only rated for flat towing setups. You can't pull a trailer with it. Instead you'll want to use the Gen-Y Hitch…

view full answer...

Answer 8

I sure can Kevin! For your 4ft. x 8ft Northern Tool trailer, I recommend the Timbren Axle-Less Trailer Suspension w/ Idler Hubs item #A20RS545. This system has a 2,000 lbs capacity and comes with idler hubs that have a 5 on 4-1/2 lug nut pattern. The…

view full answer...

Answer 9

Hey Ken, this is a really great question but the Roadmaster Invisibrake system part #RM-8700 does not have a light solution built into it as well so you would need a lighting kit as well like with the part #RM-15267. There are some aspects of the…

view full answer...

Answer 10

Hey Kevin, thanks for reaching out! The Fulton Fold-Away Coupler Hinge Kit #FHDPB230101 is definitely a good way to fix your situation and keeping the total storage size of your trailer down. The 24" length will limit you to a max 5K trailer 500…

view full answer...

Answer 11

The RockyMounts HighNoon FC #RKY74MR and MonoRail #RKY10004-10005 are very similar, but do have a few differences. The HighNoon has a 45lb per bike capacity when hauling three bikes or 60lb per bike capacity when hauling only two bikes. The MonoRail…

view full answer...

Distance From Hitch Pin Hole to Sleeve of Hitch Extender e68YR

Product Page this Question was Asked From

Continue Researching