Solution for Getting Replacement Shims for Reese Steadi Flex Weight Distribution

Question

Question:

I need the adjustment shims for this hitch. Reese Steadi-Flex Weight Distribution System w/ Sway Control

asked by: Bryan U

1

Helpful Expert Reply:

The only way to get the replacement shims for the Reese Steadi Flex weight distribution system is with the hardware kit part # RP58528 which comes with additional hardware as well.

expert reply by: Jameson C

1

Answer 1

Hi James! With your GVWR being 7,600 pounds, your loaded tongue weight should be around 760 pounds. With that said, I recommend going with the Weigh Safe True Tow Weight Distribution Hitch - 2" Shank - 6" Drop - 8.5K GTW, 850 lbs TW…

view full answer...

Answer 2

Thanks for your question James! No need for a whole new system, we have exactly what you need! Part #RP58527 will work with your #RP66558. Resee only offers them in a four pack because they will also work on the higher capacity systems like #RP66560…

view full answer...

Answer 3

The Reese Steadi-Flex Weight Distribution System w/ Sway Control - Trunnion - 10K GTW, 1K TW #RP66559 utilizes friction pads that will eventually wear down as you stated. It will take a long time for these pads to require replacing, but the…

view full answer...

Answer 4

The solution to preventing the friction pads part #RP58527 from damaging with the spring bar removal tool is the trailer jack like you mentioned. You shouldn't be using the tool to pull the bars down with that much tension. It's hard to say…

view full answer...

Answer 5

Hey Steve. The 12.5K Weigh Safe True Tow Weight Distribution Hitch item #WS94RR is going to be the best option for your Jayco trailer. You've done your homework well and with the range of 760 lbs - 1,160 lbs tongue you are not going to want to go…

view full answer...

Answer 6

The holes of the shim kit part #RP58528 that you referenced are 2-1/2 inches apart.

view full answer...

Answer 7

I spoke with my contact at Reese who said there should not be any play in the head once the bolts are properly torqued down. When installed it is possible that the bolts were not torqued to the right specs according to the installation instructions.…

view full answer...

Answer 8

It sounds like you are looking for the socket required to install the nut on a 2-5/16" hitch ball like the Curt #C40030 you were looking at. You will need a 1-7/8" socket like the 1-7/8" 12pt Thin Walled Socket - 3/4" Drive -…

view full answer...

Answer 9

Hey John, great question! The right weight distribution hitch for your setup typically depends on the tongue weight of your trailer. Is that 4,500-5,000 lbs the dry weight, something you measured, or the GVWR? Tongue weight is typically 10-15% of the…

view full answer...

Answer 10

When it comes to weight distribution hitches you really want to be right in the middle of the hitch's weight capacity range to be able to handle it when empty and fully loaded. With a GVWR of 7,500 the trailer's tongue weight would be roughly…

view full answer...

Answer 11

According to the Lippert Service Manual for the Lippert Electric Trailer Jack #LC285318. "Maintenance 1. Before each use, inspect the Power Tongue Jack and replace if bent or damaged. 2. If wiring is connected to battery terminal, inspect at…

view full answer...

Answer 12

9 inches of ground clearance will be adequate for most situations. If you need the drop that the part #17120 provides to tow your trailer level that would be the priority over ground clearance. This shank does not drop down too far so there…

view full answer...

Solution for Getting Replacement Shims for Reese Steadi Flex Weight Distribution

Continue Researching