Correct Replacement Water Heater Door for an Atwood GE16 EXT

Question

Question:

I need a replacement water heater door for my 2008 NEWMAR Dutchstar with Atwood GE16 ext hot water heater. What door do I need and can it be painted? The existing one fell off during todays drive?? Thanks!

asked by: Karl E

0

Expert Reply:

For your Atwood GE16 EXT water heater, you can use the Replacement Door for Atwood RV Water Heaters # AT91385 for a replacement door.

This door is artic white in color, but it can be repainted to whatever you want.

expert reply by: Bryce D

0

Atwood GE16 EXT
(click to enlarge)

Answer 1

Hello Brian, thanks for reaching out. Our records show the Lippert V000448334 is a standard 7,000 lb axle that uses the #25580 (1.75" ID) inner bearing and 02475 (1.25" ID) outer bearing. I do suggest you remove a hub and confirm this is…

view full answer...

Answer 2

The Replacement Door #AT91385 will fit your Atwood RV Water Heater #AT94022 (GC10A-4E) on your 2016 Jayco North Point 5th Wheel camper.

view full answer...

Answer 3

Sure can, and the correct replacement hub and drum for your trailer with a Lippert 7,000 lb axle and 8 on 6-1/2" bolt pattern is the following: - Trailer Hub and Drum Assembly - 7,000-lb Axles #LC53UD

view full answer...

Answer 4

I reached out to Lippert and the correct hub and drum assembly for your Dutchman Voltage 3200 is the Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased #LC53UD. This hub has 1/2" diameter x 1-5/16"…

view full answer...

Answer 5

Hello William, thanks for reaching out, and for providing all of that info for your axle. Your Lippert 7K axle uses a 25580 inner bearing, a 14125A outer bearing, and a 122088 grease seal - all of which can be found in the bearing kit #BK3-200. Here…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Correct Replacement Water Heater Door for an Atwood GE16 EXT

Product Page this Question was Asked From

Continue Researching