Is the Dexter BrakeRite EOH Actuator DOT Compliant?

Question

Question:

Is the BrakeRite rated as DOT compliant? I only see info about using DOT brake fluid, but was wondering about the system as a whole. thanks for your help.

asked by: Ryan F

0

Expert Reply:

I spoke with Dexter about the Dexter BrakeRite Electric Over Hydraulic Actuator # DX82KR being DOT compliant, and they said yes it is compliant and does meet the 15 minute standard, but the testing was done as a system not individually.

expert reply by: Bryce D

0

Answer 1

It sounds like you have one of 2 issues. First it could be the pump itself is damaged and unable to build pressure which would mean you are most likely going to have to get a Replacement #DX82KR. You could also have some air in the pump which you…

view full answer...

Answer 2

Hey Kevin, we have tandem axle brake line kits that would work great on your TA96BT 23-27 EZLoader boat trailer. We have the part #DM6098 which has a 15 foot main line and w have the part #DM5951 which instead has a 16 foot main line. I wasn't…

view full answer...

Answer 3

Hey Will, thanks for reaching out. What I recommend for replacing your 7-way is the following: - etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector #e99011 Wiring your connections thru the junction box helps keep them…

view full answer...

Answer 4

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 5

The Dexter BrakeRite Electric Over Hydraulic Actuator #DX82KR will need the adapter installed to be compatible with your 2007 Ford F-250 brake controller. The correct adapter is the Adapter Module for BrakeRite Electric Over Hydraulic Actuator…

view full answer...

Answer 6

Hey Dennis, I would actually avoid the Dexter actuators and instead go with the Hydrastar part #HBA16 as it's much more reliable and better performing. This is our installers favorite actuator.

view full answer...

Answer 7

The tabs on the outer Kodiak Ceramic Brake Pads #K225CP need to be bent to keep them in place on the caliper. This is done in the linked installation video at the 4:35 mark.

view full answer...

Answer 8

So the part number MKD289 is an automotive application for brake pads. If that's the style you need the correct replacement is the #K225CP which is the match. I attached a chart that has some other interesting info for picking out replacement…

view full answer...

Answer 9

Yes, the brake pads are included with the Titan Premier Disc Brake Kit #T2HRCM10DAC. Attached is a photo showing the brake pads (in blue) as well as an installation video you can refer to for when you perform the install.

view full answer...

Answer 10

The purple wire on the adapter included with the Brake Controller 7 & 4 Way Installation Kit, #ETBC7, is an auxiliary wire and can be used as a 12 volt power source, to power a reverse light or reverse lockout function for trailer brakes if…

view full answer...

Answer 11

No, the E-Coat is not to be removed from the rotors. The E-coat is a protective coat that will prevent corrosion but it will not cause issues with coating your brake pads or have any negative impact. The Dexter Disc Brake Kit - 10" Hub/Rotor - 5…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Is the Dexter BrakeRite EOH Actuator DOT Compliant?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching