Torque For Shackle Strap Bolts on MORryde Suspension Upgrade MR58ZR

Question

Question:

what is the tourque on the shakel bolts.

asked by: Butch K

0

Expert Reply:

I took a look at the instructions and the correct torque is 50 ft-lbs for the shackle strap bolts on the MORryde Suspension Upgrade Kit for Tandem Axle Trailers w/ Correct Track - 2-1/4" Shackle Straps # MR58ZR.

expert reply by: Kyle S

0

Answer 1

Hey Donnie, leaf springs typically wear out by mileage and not by age. If they haven't been used much they are going to be just fine but if they are looking flat and worn out then it's time to replace them. Since we know the axle capacity the…

view full answer...

Answer 2

Hello Mike, Great question! You can tell your toy hauler trailer's leaf springs are worn out by looking for several visual and performance-related signs. Visually, worn springs may appear flat or even bowed downward, rather than having their…

view full answer...

Answer 3

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...

Answer 4

We have seen people mount storage boxes on either side of the nose of a V-nose trailer like what you see in the picture I attached. The part #DZ91717P would work well if you have room for it like that. The dimensions of the box are 36" long…

view full answer...

Answer 5

There is no specific torque rating for the castle nut that holds your hub in place. We recommend tightening the castle nut down until it stops, and then backing it off to the next notch wheel the tang washer will fit into the castle nut. Over…

view full answer...

Answer 6

The Andersen Ultimate, part #AM3200, fits into industry standard fifth wheel base rails so it doesn't connect directly to the puck system in your 2015 Ford F-350. However, all you need is an adapter, part #RP30156, to fit into the pucks and…

view full answer...

Answer 7

Hello Jeffrey, thanks for reaching out. The link below will show you the MORryde wet bolt upgrade kit #MR46ZR instruction manual. The torque spec for the wet bolts is 50 ft-lbs. Let me know if you need anything else.…

view full answer...

Answer 8

The Correct Track Tandem Lift kit part #RR23QX cannot work with the CRE3000 kit you have on your trailer now due to clearance issues so you would need to replace them with like with the EquaFlex part #LC145546 which is also cushioned.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Torque For Shackle Strap Bolts on MORryde Suspension Upgrade MR58ZR

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching