Replacement SlideLock Covers for Thule Motion XT Cargo Box

Question

Question:

Hi, I broke the key off the lock in my Thule motion xl model 629806. When trying to remove the lock I damage the sliding mechanism. I need to replace the entire slide lock kit. Do you have a replacement for that?

asked by: Brian

0

Expert Reply:

Thule does offer the replacement slidelock covers for the Thule Motion XT # TH629706 with the part # 1401405200 for the passenger side and part # TH26RH for the driver side.

expert reply by: Jameson C

0

Answer 1

I don't have a whole lot of information for you but I spoke with Thule and they informed me that the lock core will need to come out first (with change key part #853-1251) and then the lock shield part #05771 can be removed. The lock shield…

view full answer...

Answer 2

So I'm guessing you got enough of the lock core drilled out to unlock it, is that correct? If so, you might be able to use the change key like #853-1251 to remove the core and replace it with a lock (and key) keyed to the remaining lock if…

view full answer...

Answer 3

Thule does not supply the cargo box lock mounting rivets as replacement parts; this is because these are not intended to be removed. But you certainly can substitute other hardware, and that does not necessarily even have to be rivets, to re-install…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement SlideLock Covers for Thule Motion XT Cargo Box

Products Featured in This Question

Continue Researching