Roof Rack that Fits Camper Shell Roof Rack Tracks

Question

Question:

Hello Im interested in getting some crossbars for my are bed cap but Im not sure what I need as I see you have a lot of different options I have flat roof rails from front to back of bed cap but I dont know what would fit I tried to look at pictures but I cant tell for sure

asked by: Albert C

0

Expert Reply:

It sounds like your camper shell has factory tracks on it which is what the Rhino Rack Roof Rack part # Y02-480B-NT is designed to fit. This rack was designed to fit channels just like what you have on your camper.

expert reply by: Jameson C

0

Answer 1

If you do not currently have tracks on the top of your camper the Rhino-Rack RTC-Style Roof Rack Tracks - Channel Mount - 55" Long - Qty 2 #RTC14 with Rhino-Rack Roof Rack for Factory Tracks #Y02-480B-NT will allow you to attach the roof rack to…

view full answer...

Answer 2

The Black Aero Crossbars that are the same as the Silver Crossbars, part #Y02-480-NT that you mentioned, is part #Y02-480B-NT

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 7

Hey Omar, the removable arms of the base plate kits we offer are not able to be reused on a new vehicle as they are all designed very specifically to fit the exact base plate they were made for. There are fit variations between them even on exact…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Bob, you are definitely thinking in the right direction adding rear support with that much constant weight back there. Between the 320 lbs you’re carrying full time, another 200 lbs with the kayaks, and up to 500 lbs of tongue weight, you’re…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Roof Rack that Fits Camper Shell Roof Rack Tracks

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching