Will the 1-Bike Add-On for Thule Bed Rider Pro Work With 1-1/4 x 1-1/4 Crossbars?

Question

Question:

Info states this block can be attached to square bars. What are the size limitations for the holding bracket? Specifically will it fit on 1.25" x 1.25" bar?

asked by: Thomas O

0

Expert Reply:

The 1-Bike Add-On for Thule Bed Rider Pro Truck Bed Bike Rack # TH98YC is meant to fit onto the square bars of the Thule Bed Rider Pro # TH38YC which uses a 30x20mm (1-3/16" x 25/32") square bar.

With your bars being 31.75x31.75mm (1-1/4" x 1-1/4"), they are going to be a bit too large to be clamped on. Your best bet is to use your bars t-slots if they have them or mount it directly to the floor.

expert reply by: Bryce D

0

Answer 1

Hey Robert, the Access tonneau cover part #A24AU can work with a ladder rack but it has to be one that attaches to the top of the bed rails and not one that wraps around them like the Yakima Overhaul. For a ladder rack that installs like that the…

view full answer...

Answer 2

Hi Cameron! For your 2025 Mazda 3 Sedan, I prefer the Curt #C44DR over the Draw-Tite #24982. They are almost identical and have the same weight capacities, but Curt is made in America and Draw-Tite is not. This pretty much always pushed me to the…

view full answer...

Answer 3

Hey Douglas, did your Furrion Chill Cube come with a wall thermostat? That thermostat has ability to control a furnace so you might go that route. A furnace control is typically just two or even sometimes one wire.

view full answer...

Answer 4

Easiest way to fool a brake controller into thinking a trailer is connected is going to be by installing a brake magnet on the circuit as that's the "draw" it's looking for. For that you could use the part #AKBRKR-M12 and you'd…

view full answer...

Answer 5

Hey Todd! I went out to the warehouse and measured the Hollywood Racks Bike Rack - Fork Mount - Bolt On - 15-mm Thru-Axle Skewer #HLY83FR for you. Using digital calipers I found that the inner diameter is exactly 15mm. If you need anything else let…

view full answer...

Answer 6

Yes, the Roamer LT Roof Rack for Pop-Up Campers and Camper Shells #S80510 will fit your 2023 Forest River Flagstaff 176LTD. It is also what I recommend to add a roof rack for a bicycle carrier on your camper. Once installed you will be able to add…

view full answer...

Answer 7

The Swagman Replacement Fork Mount #SP484 is designed to fit the Pick-Up Truck-Bed-Mounted 2 Bike Carrier #S64702. I was able to go out to the warehouse and measure the square crosstube of the #S64702 carrier. This square tube measures 1.190 inches x…

view full answer...

Answer 8

I went out into our showroom and measured the dimensions of a set of discontinued Thule square load bars and found that they are 7/8 of an inch by 1-1/4 inches. This is identical to the Inno square bars like #INB137.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Will the 1-Bike Add-On for Thule Bed Rider Pro Work With 1-1/4 x 1-1/4 Crossbars?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching