Recommended Replacement for a 1,600 lbs Fulton F2 Swing-Up Trailer Jack

Question

Question:

I am looking for part #9 on the Fulton F2 1600 lbs jack diagram.

asked by: Brian T

0

Expert Reply:

I spoke with my contact at Fulton and part number 9 is the gearbox which is not available as a replacement part. That part only comes with the complete assembly so you will need a new jack if that part is damaged or broken. A comparable replacement would be the Fulton F2 Swing-Up Trailer Jack item # F1413140334.

expert reply by: Jerred H

0

Answer 1

Yes Brad, that absolutely makes sense. There’s a good chance you can reuse the Dutton-Lainson welded swivel mount already on your Boatmate trailer. The Dutton-Lainson #DL22339 uses a standard swivel-mount design, I attached a photo of the mounting…

view full answer...

Answer 2

Hi Mike, that’s a great question and I totally get why you’d want something that lines up with your existing holes and bolts right on without any guesswork. The honest answer is that the Fulton F2 uses a unique mounting pattern, so there really isn’t…

view full answer...

Answer 3

Hey Tim. There are only two jacks that will fit your current mounting bracket and they are both Fulton F2 jacks rated at 1,600 lbs. I have listed them below: Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind item #F1413060334 Fulton F2…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 7

Hey George, best solution for you will be to go with an all new jack like the etrailer part #e95YV because Fulton is no longer in business so there isn't a way to get a replacement F2 and none of the other jacks out there use the same bolt…

view full answer...

Answer 8

It sure does Steve! Our 3,500 lbs etrailer Electric Trailer Jack w/ Tongue Weight Scale item #e43KV also comes in a 5,000 lbs capacity. We have two different options depending on how you want to power it that I have listed below: Wired to Trailer -…

view full answer...

Answer 9

Hey Seth, The etrailer Electric Trailer Jack w/ 7-Way - Drop Leg - A-Frame - 18" Lift - 5K #e74GV may work on your 2015 Ford F-250, but there's a high chance that it won't straight out of the box. On 2015 and newer Ford trucks with a…

view full answer...

Answer 10

Hey Will! The square tube on the Bigfoot Hydraulic Trailer Jack #BF94FR is 4" x 4". What kind of trailer do you have?

view full answer...

Answer 11

Hey Brian! Yep, for your boat trailer, I’d skip the etrailer A-frame drill jack #e38AV since your trailer doesn't have that standard 3-bolt A-frame jack mount. That could be fabricated to fit, but that's a lot of unnecessary work. For a…

view full answer...

Recommended Replacement for a 1,600 lbs Fulton F2 Swing-Up Trailer Jack

Continue Researching