Replacement Bolt For Yakima FullSwing 4-Bike Rack

Question

Question:

Looking for replacement hardware to mount a Yakima fullswing 4 hitch rack. Schematic shows two different bolts One with two washers and a bolt and a second with a single locking washer.

asked by: Pam H

0

Expert Reply:

There is just a single bolt for the Yakima FullSwing Bike Rack for 4 Bikes # Y02465, and for that along with the needed wrench, the correct replacement is the following:

- Replacement Hardware Bag # Y52XR

expert reply by: Kyle S

0

Answer 1

Since you confirmed the Autowbrake Electric Brake Controller #3430001 had 12v power running to it the only only other thing to really check would be that the rest of the 5 wires were spliced into the proper circuits. With proper power and ground even…

view full answer...

Answer 2

The Yakima Threaded Hitch Bolt, part #Y8890200 is 5/8 inch in diameter and a 4-1/4 inch overall length, as shown in the provided photo. The StickUp originally included two different hitch bolts, one for the 2 inch hitch and a shorter one for the…

view full answer...

Answer 3

Based on your description of your older Yakima rack (black non-folding single arm), my contact there indicated that what you have may actually be their Rocn'Gate rack. For this rack the correct threaded bolt is not the item #Y8890176 you…

view full answer...

Answer 4

Hey Ak, thanks for reaching out! The Replacement Anti-Rattle Hitch Bolt and Washer for Yakima HangOver Bike Rack #Y52FR has a 4-5/8" overall length. I've attached a photo of this for your reference. Are you needing to replace the hitch pin…

view full answer...

Answer 5

Sometimes with bike racks like the Yakima FullSwing #Y02465 that have knob anti-rattle devices the trick to getting them to get rid of all of the movement is to use one hand to move the bike rack around in the hitch and the other to tighten firmly on…

view full answer...

Answer 6

If you look at the provided diagram, you can see the replacement parts that Yakima offers for your Ridgeback Bike Rack. If what you're needing isn't shown, please let me know what you're needing. Zip strips #Y8890297 Endcap #8890306…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Replacement Bolt For Yakima FullSwing 4-Bike Rack

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching