Are The Deka 4-Wire and 7-Wire Jacketed Wires Made Of Copper Or CCA

Question

Question:

The trailer wire you sell. Either the Deka 7 wire or the 4 wire. Is the wire copper or CCA wire?. thank you

asked by: Gene

0

Expert Reply:

The Deka Jacketed 4-Wire # DW04923-1 and 7-wire # DW04914-1 both use full copper wire instead of Copper Clad Aluminum (CCA) wire.

expert reply by: Kevin C

0

Answer 1

For the brake circuit of your trailer you will want to run 10 gauge wire like our part #10-1-1 which is sold by the foot and is standard copper primary wire. We use it all the time here on trailers and it works great. For bonded 14 gauge wire that…

view full answer...

Answer 2

Super high-efficiency LED-type lights such as the Optronics #STL211RCB draw so little amperage (current) that you can wire them on your 20-foot trailer using 14-gauge (or heavier) wiring. We offer 10-gauge wire #10-1-1 by the foot. You will want to…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Are The Deka 4-Wire and 7-Wire Jacketed Wires Made Of Copper Or CCA

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching