Can Equa Flex Equalizer be Used with Correct Track Alignment Kit

Question

Question:

Can this equalizer be used with gen 3 correct track alignment kit?

asked by: Mark

0

Expert Reply:

Yes, the EquaFlex equalizer kit part # LC279688 is compatible with the Correct Track alignment kits like you have.

expert reply by: Jameson C

0

Answer 1

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 2

We do have a note on this issue: Will not work with E-Z Flex suspension systems due to the length of the wet step bolts. Assuming you could obtain wet bolts that are long enough you could use Correct Track with the E-Z Flex suspension system.…

view full answer...

Answer 3

I understand your worry Tom, and I have a couple recommendations. First is the MORryde ALLTREK 4000 Shock Absorbing Equalizers #MR89DR which has a height of 4-1/2" for the mounting bolts. This is also 6-1/2" in width like the shorter…

view full answer...

Answer 4

Hey Jack, the Furrion Chill HE RV unit like the part #FR52PR is going to be your best solution. It is the quietest and draws the lowest amount of power at 11.2 amps compared to most similar options that are around 15. We've tested all of the…

view full answer...

Answer 5

Hey Ryan, since this is a bedroom AC unit I would recommend going with a quieter AC unit like the Furrion Chill Cube part #FR27TD which is by far the quietest and coldest blowing option available. This is also designed to fit into a RV roof vent…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Can Equa Flex Equalizer be Used with Correct Track Alignment Kit

Continue Researching