What Size Mounting Hardware Does The etrailer Receiver Use For Attaching To 2000 Toyota 4Runner?

Question

Question:

What size bolts are used for the tow bar for a 2000 4Runner?

asked by: Kimberly E

0

Expert Reply:

The etrailer Trailer Hitch Receiver # e37KR is attached to your 2000 Toyota 4Runner using four 1/2"-13 grade 5 bolts which are 1-1/2" long. You will also need four 1/2" conical washers. We do offer all the mounting hardware with our Replacement Hardware Kit # RHK if you prefer to not have to go source your own hardware. Be sure to enter the hitch item number when ordering the replacement hardware to ensure you get all the correct components.

expert reply by: Bud M

0

Answer 1

We do have the replacement hardware for the etrailer Trailer Hitch Receiver #e37KR. What you need is the Replacement Hardware Kit for Trailer Hitches #RHK. Make sure you add e37KR into the open field under "Hitch Item Number" before you add…

view full answer...

Answer 2

I recommend picking up the etrailer Trailer Hitch Receiver #e37KR and the Curt T-Connector Vehicle Wiring Harness #C55341 for your 1997 Toyota 4Runner. The etrailer hitch has a matte black finish that's more durable than the glossy black finishes…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

I may have an alternate option available that will require drilling to get installed, but with your 1996 Toyota Prado not being an American market vehicle, I cannot confirm the fit of any hitch we carry. I did include diagrams for the Curt #13445 and…

view full answer...

Answer 7

I attached a picture that has the install instructions for the Curt hitch #C13087 that you have as well as a link to them on this page as well. Sometimes the instructions are stuffed down the hitch tube opening which can make them harder to find.

view full answer...

Answer 8

Hey Aaron, the distance between the mounting holes from side to side on the etrailer hitch part #e37KR is 39-5/8 inches. I attached a picture that has the other dimensions listed as well.

view full answer...

Answer 9

I do have a solution, but there are no custom fit hitches with a bolt-on installation for your 1997 Toyota Hilux Surf SSR-X. The only option is to use a universal hitch like the Curt Class 5 #C47CR. This weld-on hitch fits vehicle frames up to…

view full answer...

Answer 10

Hey Peter, so according to the instructions for the Curt Trailer Hitch Receiver #C38BR, Curt recommends you tighten all M12 hardware to 86 ft-lbs.

view full answer...

Answer 11

When it comes to installing a trailer hitch on your 2000 MCI 40 foot Intercity Bus we do not have a custom hitch that would fit but you can weld on The Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2 inch Receiver - 44 inch Wide #C37CR. The…

view full answer...

What Size Mounting Hardware Does The etrailer Receiver Use For Attaching To 2000 Toyota 4Runner?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching