4-Way Trailer Wiring Harness for 1997 Ford E350

Question

Question:

We have ford 1997 E350 econoline van. The wiring harness part we need is discontinued. F7UZ 13A576-BC. I have attached pics of what the van has. Would u have harness that we are able to tow with?

asked by: Mari

0

Expert Reply:

I have an easy way to install a 4-way on your 1997 Ford E-350 with the Tekonsha harness part # 118344 but we don't have a way to use the factory connector that you have right now. The Tekonsha harness installs by plugging inline with the taillight connectors to provide a 4-way connector.

expert reply by: Jameson C

0

Answer 1

Since your 2011 Ford E-350 does not have the factory towing package you will need to start with adding a 4-way connector. I recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56020 which will plug into your…

view full answer...

Answer 2

To replace the factory hitch on your 2002 Ford E-350 Super Duty Van you can use the Draw-Tite Ultra Frame #41945 which has the bolt holes 38-5/8" apart (center on center). This hitch will be the perfect replacement for your factory hitch.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

4-Way Trailer Wiring Harness for 1997 Ford E350

Continue Researching