What Are The Gear Ratios For The Square 2-Speed Jack w/ Crank # TJD2SP-12000SP-F?

Question

Question:

What the the gear ratios

asked by: Camden F

0

Expert Reply:

The Square 2-Speed Jack w/ Crank # TJD2SP-12000SP-F has a high gear ratio which is 6.43 handle revolutions per inch of travel, and the low gear ratio which is 22.86 handle revolutions per inch of travel.

expert reply by: Bud M

0

Answer 1

The Ram Square 2-Speed Jack part #TJD2SP-12000SP-F does not have any sort of compatible powered drive kit available. That said, if you were to go with the Bulldog Square 2-Speed Jack part #BD183816 you could then use the Bulldog Powered-Drive Kit…

view full answer...

Answer 2

These are both great questions! Jacks with 2 speeds have the gears changed by either moving the handle to a different spot on the jack, or having the handle pushed in or pulled out to change the gear that is engaged- with this specific jack,…

view full answer...

Answer 3

We definitely have some trailer jacks you can use as a replacement for your Dutton-Lainson but it doesn't look like anything we have will work as a direct replacement. If you'd like to stick with the Dutton-Lainson brand then I recommend…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Hi Stephanie! Great question and you’re totally right to ask, because most hitches for the 2024 RAV4 do require a bit of bumper trimming. That includes the Oris Detachable Hitch #TS66VR, since it uses a hidden design that needs a hole cut in the…

view full answer...

Answer 12

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

What Are The Gear Ratios For The Square 2-Speed Jack w/ Crank # TJD2SP-12000SP-F?

Product Page this Question was Asked From

Continue Researching