Max Lock Shackle Diameter for Blaylock EZ Lock Trailer Coupler Lock

Question

Question:

WHAT IS THE DIAMETER OF THE HOLE IN THE SECURE PIN? WILL A LOCK WITH THE SHACKLE DIAMERTER OF 7/16 in FIT? BASICALLY IM TRYING TO USE IT WITH A LOCK Abus #190CS/60 WILL IT FIT? THANKS!

asked by: ROBERTO T

0

Expert Reply:

The max shackle diameter for the Blaylock EZ Lock Trailer Coupler Lock part # BLTL-33 is 3/8". It's designed to be used with the Master Lock Stainless Steel Padlock part # ML40D or similar which has a 3/8" diameter shackle.

expert reply by: Conner L

0

Answer 1

While we do have some step solutions for you, none of the traditional style steps have the top step level with the mounting brackets when they are pulled out and/or a bracket mounting width of 29" wide (which is much wider than normal). For your…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Adam, the correct Kuat DEK Platform rack with light bar for your 2026 Toyota Tacoma would be the part #KU73SR. The correct Kuat Ibex Overland Truck Cap then too would be the part #KU99SR that you referenced. Now the top of this would be lower…

view full answer...

Answer 6

Hey Dustin. I installed the Enclosed Trailer Transition Plate item #M368FR on a trailer here when we first got them in and you're good! That plate is single solid piece of steel. It's got a heavy duty piano style hinge that has been riveted…

view full answer...

Answer 7

Hello Leon, I am sorry but you will not be able to secure a chain inside the ICON Trailer Coupler Lock for Cast 2-5/16" Ball Coupler - Cast and Stainless Steel - Black #AL98DQ. The ICON locks are built like Fort Knox, if there were extra room…

view full answer...

Answer 8

Hey Mike, The #IR29FR lock kit is not compatible to work with the B&W Pintle Hitch that you have. The pin diameters are different sizes and would not fit. The only kit we have that is confirmed to fit the B&W Pintle Hitch is the InfiniteRule…

view full answer...

Answer 9

Hi Richi! The etrailer Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 5 - Pre-Greased #AKIHUB-550-35-EZ-K you asked this question from fits all your specifications. It works with 3,500 pound axles (it uses the standard #L44649 and…

view full answer...

Answer 10

Hi Mark; we don't know all of the differences between those different models, and only the #DOM67FR remains available. All of the others have been discontinued. Dometic makes slight changes and upgrades over time but those typically aren't…

view full answer...

Answer 11

The Bulldog Gooseneck Coupler Head Repair Kit #BD1542S01 is specifically for the #BDGN240200 coupler head. This is the Bulldog GN24 which is the same as the Fulton GN24.

view full answer...

Answer 12

Hello Bob, thanks for reaching out. We have a few option for locks that will fit the Dexter DX7 coupler. For a locking pin I recommend the etrailer Surge Brake Coupler Lock #e98888. This will allow you to lock the coupler to the ball. The picture…

view full answer...

Max Lock Shackle Diameter for Blaylock EZ Lock Trailer Coupler Lock

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching