Torque Spec for Install of Lippert Ground Control 3.0 Replacement Jacks

Question

Question:

I need a manual to get the Torque settings when I Replace my 24-1/2 Left Rear Leg - Lippert Ground Control 3.0 Electric Leveling System Item # LC305339. Also any other hints you may have. Thank you

asked by: Hugh A

0

Expert Reply:

I attached a link to the install instructions for the Lippert Ground Control 3.0 part # LC675817 which is the kit the leg part # LC305339 is a part of. On page 6 of the instructions is the torque spec for mounting the jacks. Spoiler alert...it's 75 ft lbs.

expert reply by: Jameson C

0

Answer 1

Hey Derek, we actually have replacement drain tubes for the Pace Edwards JackRabbit with the part #PE55TJ which would be what you would want to use over the Retrax drain tubes.

view full answer...

Answer 2

Thank you for the picture with the measurement of your current Lippert Ground Control right rear leg that measures 24-1/2 inches from top to bottom when retracted. Based on that the correct replacement is the part #LC344792 and not the one you…

view full answer...

Answer 3

There have been 2 different heights of smaller legs that come with the Lippert Ground Control 3.0 #LC675817 over the years so you'll need to measure and see if you have the 22-1/2" or the 24-1/2" rear legs in order to choose the correct…

view full answer...

Answer 4

It sounds like you are needing to replace one of the rear legs for your Lippert Ground Control leveling system. The Rear legs have a mounting plate with 11 holes. So I believe we are on the same page here. There are going to be a few options for the…

view full answer...

Answer 5

The Ground Control jacks for travel trailers are different as they are a C-jack instead of a vertical lift. I recommend using the Replacement C-Jack for Lippert Components Electric Ground Control TT #LC404488 for that application instead of combining…

view full answer...

Answer 6

Hey TJ, I went out and opened up one of the Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System #LC324269 boxes and found that they include a 5/8-18 x 1-1/2" fine thread grade five bolt. I then called Lippert and they…

view full answer...

Answer 7

We do have the replacement motor #LC343758 which will replace the Hall effect motor for your Lippert Ground Control 3.0 6-point electric leveling system. If you are looking for the 6 point controller it will be part #LC85ED. You can see our current…

view full answer...

Answer 8

If both middle jacks are not retracting or extending on your #LC675817, odds are one or more of the fuses is out. There is a fuse for each of the legs and if one of these is bad, it will definitely cause the legs not to work. This can be mounted just…

view full answer...

Answer 9

Please note the linked Installation Instructions for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System, #LC675817 that identify manufacturer's stated torque values for hardware. I have also included an installation video as…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Torque Spec for Install of Lippert Ground Control 3.0 Replacement Jacks

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching