Torque Values for Installation of Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System

Question

Question:

I noticed that a couple of the jack bolts are loose and was wondering how much torque is needed when tightening them

asked by: Keith V

0

Expert Reply:

Please note the linked Installation Instructions for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System, # LC675817 that identify manufacturer's stated torque values for hardware. I have also included an installation video as well.

We have a very cost effective 0 - 150 ft. lbs.1/2" Drive Torque Wrench, # PTW3001C if needed.

expert reply by: Michael R

0

Answer 1

I attached a link to the install instructions for the Lippert Ground Control 3.0 part #LC675817 which is the kit the leg part #LC305339 is a part of. On page 6 of the instructions is the torque spec for mounting the jacks. Spoiler alert...it's 75…

view full answer...

Answer 2

Hey TJ, I went out and opened up one of the Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System #LC324269 boxes and found that they include a 5/8-18 x 1-1/2" fine thread grade five bolt. I then called Lippert and they…

view full answer...

Answer 3

The middle and rear jack mounting brackets of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set #LC675817 that you referenced are a total of 6 inches in width. That's how much free room…

view full answer...

Answer 4

If both middle jacks are not retracting or extending on your #LC675817, odds are one or more of the fuses is out. There is a fuse for each of the legs and if one of these is bad, it will definitely cause the legs not to work. This can be mounted just…

view full answer...

Answer 5

Hey Roy, thank you for the pictures of the awning head covers you have as that makes knowing what you need as a replacement a lot easier. Based on seeing them the correct back cover would be the part #LC289567 but since you need the front cover as…

view full answer...

Answer 6

Unfortunately, there is not Kenny. If your Replacement Front Jack for Lippert Ground Control 3.0 Leveling System item #LC362485 is damaged or not functioning correctly the only option available is to replace it. The Replacement Front Jack item…

view full answer...

Answer 7

Hey Robert! That Stromberg Carlson foot won't work but we actually do have the replacement SnapPad for your leveling system. The Replacement Pad for SnapPad Jack Stand Pad System - 9" Round Jack Foot #SP54FR is what you need. It works with…

view full answer...

Answer 8

Yes, the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote #LC675817 will offer a much more stabilized base for your 2012 Keystone Raptor than the OEM scissor stabilizers. That being said, you may not be able to…

view full answer...

Answer 9

Hi William, Thanks for the question. Based on your setup, I don't think the Air Lift LoadLifter 5000 kit, part #AL57541, is going to be the right fit. Once the factory pickup bed is removed and a Norstar utility bed with a gooseneck is installed,…

view full answer...

Answer 10

Yes, we do offer replacement jacks for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 6-Point Set part #LC675817. I have attached these for you below by their location on the trailer. Rear/Middle: 24-1/2" Leg part…

view full answer...

Torque Values for Installation of Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching