MORryde X-Factor Crossmember Fit for Standard Frame Hangers with Correct Track

Question

Question:

Do you have the morryde x factor # mr69zR?

asked by: Marvin G

0

Expert Reply:

Thanks for reaching out!

The MORryde X-Factor Crossmember for Stock Leaf Spring Suspension with Correct Track MR69ZR was discontinued back at the end of 2022 but you can piece it together using the MORryde X-Factor Crossmember for Standard Frame Hangers # MR33WR and the Adapter Kit for Correct Track Hangers # MR93WR.

I've attached some review videos for you to check out!

expert reply by: Jon G

0

Answer 1

Hello again Adam! Since you have 7k Lippert axles the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers #RM-2460-2570 is the correct kit. This is going to be a significant improvement over the stock suspension. For wet bolts you…

view full answer...

Answer 2

The MORryde X-Factor Crossmember Adapter Kit for Correct Track Hangers part #MR93WR which is designed to be used with the MORryde X-Factor Crossmember for Standard Frame Hangers part #MR33WR is used on the outside hangers for trailer's with…

view full answer...

Answer 3

Hey Richard, thanks for reaching out! Yes, the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR can be installed with the Roadmaster Comfort Ride #RM-2460-2570. Just as long as the X-Factor is installed on either of the end hangers as…

view full answer...

Answer 4

I would be happy to help! The Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers - Tandem 7K Trailer Axles #RM-2460-2570 is for trailers that have 7000lb tandem axles, and use springs that have a 3500lb capacity each (one spring on…

view full answer...

Answer 5

Hey Henry, with leaf springs like the part #EM28AJ there isn't a torque spec for the shackle bolts that secure them as they need to be able to move freely. So the trick is to use lock nuts so they won't back off. So using them snug them up by…

view full answer...

Answer 6

Hello Alan, thanks for reaching out. We likely will have a brake drum that will fit your trailer, but I do not have a way to accurately recommend a drum based on the info from the backing plate you provided. The numbers you provided indicate a Dexter…

view full answer...

Answer 7

Hey Dave, since you have 7k axles I would recommend just going with the 7k tandem Roadmaster Comfort Ride part #RM-2460-2570 as it's the correct rating and has correct size components. But if you wanted to go with the 8k kit part #RM-2460-2580…

view full answer...

Answer 8

Hey Zoniezz, thanks for reaching out! That flat pieces with the 3 holes from the MORryde X-Factor Crossmember Adapter Kit #MR93WR are spacers, and they can be placed between the mounting brackets and the crossmember (see blue highlight in linked…

view full answer...

Answer 9

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 10

I definitely see what you're saying about the spacer, found as part #LC34UD, from the 2nd gen Correct Track LC407131. With that being said, the Correct Track Trailer Alignment and Lift Kit #RR23QX has been safety tested and works just fine…

view full answer...

Answer 11

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 12

Yes, you are able to use the MORryde X-Factor Crossmember #MR33WR but on the Correct Track front and rear hangers you would also need the Adapter Kit #MR93WR. I do not see any plumbing or other components on your 2018 Highland Range Open Range 374BHS…

view full answer...