Replacement Hardware for Curt Hitch 13390 On 2013 Subaru Outback Wagon

Question

Question:

Someone trying seller me 13390 hitch for my 2013 outback Fo u sell installation bolt for this hitch?

asked by: John K

0

Expert Reply:

The Curt Trailer Hitch Receiver part # 13390 is a fit for a 2013 Subaru Outback Wagon. If you're looking for replacement hardware we do offer this as the Replacement Hardware Kit for Trailer Hitches part # RHK. This comes with everything the hitch would have come with when new.

expert reply by: Conner L

0

Answer 1

The Trailer Hitch Spacer Block #RP3022 that you referenced is sold individually.

view full answer...

Answer 2

If the conical washers on your EAZ weight distribution hitch are 3/8" washers, then the Draw-Tite Trailer Hitch Conical Tooth Washers - 3/8" Diameter #01292006-020-01 would work just fine. Since it's just a conical washer you're…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Replacement Hardware for Curt Hitch 13390 On 2013 Subaru Outback Wagon

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching