Replacement 4-Pin Switch for RV Awning

Question

Question:

I am looking for an awning in-out rocker switch with 4-pin attachment. I have a 2021 Jayco Jay Flight SLX265RLS towable 31 RV.

asked by: Theodore R

0

Expert Reply:

We do have awning power switches with four wires in both black and white, the Replacement Switch Kit for Solera Power RV Awnings part # LC285499 for white or part # LC285500 for black. Please note, if your wire colors don't match you will need to match them by function using the diagram below. The dimensions of the switch are 3-1/2" long x 3" wide.

expert reply by: Conner L

0

Replacement 4-Pin Switch for RV Awning
(click to enlarge)

Answer 1

I attached a wiring diagram for the Solera Power Awning Switch Kit #LC285500 for you to check out.

view full answer...

Answer 2

Hey Tom, yeah it does look like the Replacement Switch Kit for Solera Power RV Awnings #LC285500 will still work as a replacement for your Solera awning. This switch will replace the switch on any 12v Solera awning, so it'll work fine with yours.…

view full answer...

Answer 3

The Solera Power Awning Switch Kit #LC285500 does have 6 pins on the back of it, the included harness just has two internal jumper wires running between a few of the pins making it so there are only four wires. Since your switch has 6 individual…

view full answer...

Answer 4

Everything I could find on the switch for a Dometic 9100 Power Awning is that the correct switch is the 3310455.062. While we do not carry that exact switch, it is a 4 wire design. This means you can use the Replacement Switch Kit #LC285500. Because…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement 4-Pin Switch for RV Awning

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching