Best Place To Set A Ground On A Utility Trailer

Question

Question:

For a utility trailer is it okay to connect a ground wire from each of the two tail lights to the ground wire coming out of the trailer four way connector instead of using the trailer frame as a ground?

asked by: Randy

0

Expert Reply:

You should have no problems connecting the ground wire from your light to the main ground circuit on your utility trailer. Though we typically recommend using a Ring Terminal # DW05702-1 and a Self Tapping Screw # FA1131822 to ground it to your trailer frame as this will give you a better connection. You could also ground through the mounting studs that are in direct contact with the trailer frame or by having a jumper wire ran from the lamp to the trailer frame.

If you have any further questions please feel free to reach back out to me and I would be more than happy to further assist you.

expert reply by: Noah E

0

Answer 1

Basically you have it figured out pretty well already. The Curt and Tekonsha are going to be quite a bit easier to install since you don't have to route a power wire, but the Hopkins overall will be the safer and more reliable option since it has…

view full answer...

Answer 2

You will want to first try connecting and disconnecting the driver side connectors of the part #C55451 to hopefully clear out any misconnection that it may have. If it still doesn't work you would want to test the converter box to determine if it…

view full answer...

Answer 3

I am sorry to hear about the issues you are having with the Curt T-Connector Vehicle Wiring Harness part #C55451. This harness actually ties in behind the tail lights on your 2006 Jeep Grand Cherokee so there will be no additional fuses or relays…

view full answer...

Answer 4

If the Hopkins Plug-In Simple Wiring Harness #HM42545 you referenced keeps blowing fuses in the vehicle then there is likely damaged wiring somewhere that's causing a short. I recommend inspecting the wiring on the harness for any exposed,…

view full answer...

Answer 5

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Best Place To Set A Ground On A Utility Trailer

Products Featured in This Question

Continue Researching