Tensioners to Use with Titan Tire Chains part # TC2327

Question

Question:

Do you recommend these supplemental tensioners or a different set for the Titan chains TC2327? It looks like those chains come with a tensioner albeit only one strap - single point of failure, so would these multi-point tensioners be better? This is for a Toyota Sequoia Platinum with 20 inch wheels P275/55R20. Also, these tensioners look like theyd have less risk of scratching, but dont want to use them if thats not advised for some reason. Thanks in advance.

asked by: BRIAN D

1

Helpful Expert Reply:

A set of tensioners like the part # TCMA3 are a great idea with the Titan tire chains part # TC2327 that you mentioned. Since these are rubber they would not scratch your wheels at all. The Titan chains don't normally require additional tensioners but it can't hurt to use them and they will help keep the chains nice and tight on the tire.

expert reply by: Jameson C

1

Answer 1

Hello Spencer. For deep snow and ice you are actually going to want the same kind of chain, the Titan Chain Snow Tire Chains for Wide Base Tires - Ladder Pattern - V-Bar Links - 1 Pair #TC3831 would be a great fit for your F350 with tire size…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Tensioners to Use with Titan Tire Chains part # TC2327

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching