Parts Needed to Install BrakeMaster Braking System in 2020 Ford Ranger

Question

Question:

what parts do I need to install the RM-9160

asked by: Wayne J

1

Helpful Expert Reply:

To install the Roadmaster BrakeMaster part # RM-9160 that you referenced in your 2020 Ford Ranger will require the brake seat adapter part # RM-88349 and the brake light relay part # RM-88400 and you'd be set.

expert reply by: Jameson C

1

Answer 1

Yes, the Roadmaster Crossbar-Style Base Plate Kit part #RM-524459-4 is a confirmed fit for your 2019 Ford Ranger XLT SuperCab 4x4. There are no differences between the Lariat and XLT trim packages in regards to the fit of a base plat kit such as the…

view full answer...

Answer 2

Yes, you can reinstall the Roadmaster BrakeMaster System w BrakeAway for RVs w Air or Air Over Hydraulic Brakes - Proportional item #RM-9160 in your new 2022 Ford Maverick. Since your Maverick is a hybrid you will also need the RoadMaster BrakeMaster…

view full answer...

Answer 3

The most common locations for mounting the air reservoir portion of the Roadmaster BrakeMaster #RM-9160 are next to the driver's seat and under the dash near the left kick panel. If there is no room under the hood of your vehicle this would be a…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 8

Thanks for the information Kevin! To flat tow your 2025 Ford Bronco with a standard bumper and LED lights, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect item #e84ZR Base…

view full answer...

Answer 9

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

Hi Brian, To flat tow your 2026 Ford Ranger XLT with your Blue Ox Avail Tow Bar, you'll need: - Blue Ox Base Plate Kit w/Removable Arms part #BLU77ER, this will require some minor drilling, and the tow hooks must be removed and remain off the…

view full answer...

Parts Needed to Install BrakeMaster Braking System in 2020 Ford Ranger

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching