Height Of Roadmaster Spare Tire Carrier # RM-195125 From Hitch Center To Spare Tire Center

Question

Question:

What is the distance from the center of the spare tire mounting plate to the center of the receiver tube. Trying to find out how far the spare tire will sit above the receiver tube. Thank you!

asked by: James H

0

Expert Reply:

The Roadmaster Spare Tire Carrier # RM-195125 is going to have a height of 24" from the center of the receiver to the center of the spare tire mount.

expert reply by: Bud M

0

Answer 1

The Roadmaster Spare Tire Carrier #RM-195125 is going to likely be your best option. The only other option would be a Carrier #e98ZR you would have to remove to open the door. I have added an image with the length of the carrier below as you may…

view full answer...

Answer 2

The Roadmaster Spare Tire Carrier #RM-195125 pivots to the side as opposed to folding down so the height when doing that would only be to the top of the bracket, which is 7-1/2 inches. When it is in the upright position, the overall height will of…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Answer 8

Hey Matt, welcome back! You are correct. The threaded hole on the Weigh Safe 180 Hitch 2-Ball Mount for 3" Hitch item #WS34MR ball retainer, is to make removing the pin easier. You can insert a 1/4"-20 screw to get additional leverage to…

view full answer...

Answer 9

Hi Cory, can you tell me the specific part numbers and which measurements you want exactly? I only see that you looked at some Trimax HD ball mounts, and I want to make sure I'm getting all of the measurements you're looking for and on the…

view full answer...

Answer 10

Hi John! The BulletProof Aluminum Hitch w/ Stainless Steel Dual Ball for 2" Hitch - 4" Drop/Rise - 14K #BPH32YR is anodized, so it isn't just raw aluminum. That actually goes for all of BulletProof's aluminum ball mounts, which is…

view full answer...

Answer 11

Hey Adam, the correct Kuat DEK Platform rack with light bar for your 2026 Toyota Tacoma would be the part #KU73SR. The correct Kuat Ibex Overland Truck Cap then too would be the part #KU99SR that you referenced. Now the top of this would be lower…

view full answer...

Answer 12

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...